Mon-Fri: 7AM-8PM, Sat: 8AM-6PM, Sun: 9AM-5PM Licensed & Insured [email protected] Serving Latimer, MS

CHI Overhead Doors Garage Door Roller Replacement in Latimer, MS

Worn steel or plastic rollers swapped for quiet, sealed nylon rollers. Typical cost $150-$350.

From the first phone call to the final safety test, CHI Overhead Doors garage door roller replacement in Latimer, MS follows a simple process: diagnose, quote, repair, test. Worn steel or plastic rollers swapped for quiet, sealed nylon rollers. We work on CHI Overhead Doors garage doors of every age, from older models to current lines, and carry or can source compatible parts. CHI Overhead Doors builds residential and commercial sectional doors in Arthur, Illinois, and sells them through independent dealers.

Is it time for CHI Overhead Doors garage door roller replacement?

  • Grinding, squealing or rumbling as the door moves
  • The door shakes or jerks in the track
  • Cracked, chipped or wobbly rollers
  • Rollers that no longer spin freely

Common causes

  • Worn-out bearings in steel rollers
  • Cracked builder-grade plastic rollers
  • Rust or dust packed into the bearings

What you can check yourself

  • Watch the rollers while the door moves. They should roll, not slide.
  • Look for cracked plastic wheels or wobbling stems.
  • Leave the bottom rollers to a technician. They sit in brackets that hold cable tension.

Still stuck? Our free symptom checker and troubleshooting wizard walk you through it step by step.

Our CHI Overhead Doors garage door roller replacement process

  1. Inspect every roller, hinge and track section
  2. Replace rollers one hinge at a time, with sealed nylon rollers for a quieter door
  3. Replace the bottom rollers safely with tension controlled
  4. Lubricate hinges and bearings
  5. Test for smooth, quiet travel

CHI Overhead Doors Garage Door Roller Replacement cost in Latimer, MS

$150-$350Typical range, parts & labor
about 1 hourTypical time on site

What moves the price:

  • Door size and weight (single or double, steel or wood)
  • Which parts need replacing and whether they are in stock
  • Spring type and cycle rating
  • Emergency or after-hours timing

These are typical U.S. ranges, not a quote. You get an exact price for your door before any work starts. For a quick estimate, try the repair cost calculator.

Other CHI Overhead Doors services

Serving Latimer, MS and nearby towns

Humid air in Mississippi rusts cables, roller bearings and hinges, which makes the door noisy and heavy and eventually makes the opener strain.

Close to the coast, salt air speeds up corrosion. Galvanized or coated springs, nylon rollers and stainless hardware hold up better than bare steel.

Technicians serve all of Latimer, plus Saint Martin (6.7 mi), Gulf Hills (7.3 mi), D'Iberville (7.6 mi) and Ocean Springs (8.8 mi). Call (833) 435-8883 to book a visit in Latimer.

CHI Overhead Doors Garage Door Roller Replacement: frequently asked questions

How much does CHI Overhead Doors garage door roller replacement cost in Latimer, MS?

CHI Overhead Doors Garage Door Roller Replacement typically costs $150-$350 including parts and labor, and usually takes about 1 hour. The exact price depends on your door and the parts it needs, and you get it before any work starts. Call (833) 435-8883 for a quote.

Can you do CHI Overhead Doors garage door roller replacement the same day?

Often, yes. When a technician is available we can usually come the same day, and common parts are carried on the truck. Doors that won't close or have a broken spring are treated as priority calls, and emergency service is available.

Is CHI Overhead Doors garage door roller replacement covered by a warranty?

Our work comes with a 90-day labor warranty on repairs. New parts and doors also carry the manufacturer's warranty, and CHI Overhead Doors warranty terms vary by product and age. Ask for the warranty details in writing with your quote.

Are your technicians licensed and insured?

Our technicians are insured, and where Mississippi or Latimer requires a contractor license for garage door work, the job is done under that license. You're welcome to ask for proof when you book.

Should I repair or replace my garage door?

A good rule of thumb: if the repair costs more than about 50% of a replacement, or the garage door is near the end of its life, replace it. A garage door typically lasts 15 to 30 years. If several panels are damaged, the door is rusted through or rotted, or parts are discontinued, replacing it is often better value. Springs are the exception: a broken spring is always replaced, never repaired. Our free repair vs. replace calculator can help you compare.

More services

Popular Garage Door Services in Latimer, MS

Clopay Garage Door Repair

Clopay is one of the largest residential garage door makers in North America, with lines such as Classic, Modern Steel, Coachman and Canyon Ridge. The model is usually printed on a label on the door's end stile, which helps us match replacement panels.

Typical $150-$450

Hörmann Opener Gear & Sprocket Replacement

Stripped drive gears replaced so the motor moves the door again.

Typical $125-$275

Linear Opener Circuit Board Replacement

Linear openers and remotes are now part of Nice North America. Linear's MegaCode remotes are common on older openers and gate systems.

Typical $175-$400

Midland Garage Door Extension Spring Replacement

Side-mounted extension springs replaced in matched pairs, with safety cables installed.

Typical $150-$350

Amarr Garage Door Repair

Amarr, an ASSA ABLOY Group brand, makes residential lines such as Classica, Heritage, Lucern and Oak Summit, as well as commercial doors.

Typical $150-$450

Raynor Garage Door Repair

Raynor, based in Dixon, Illinois, makes residential and commercial garage doors as well as openers.

Typical $150-$450

Midland Garage Door Torsion Spring Replacement

Torsion springs replaced and wound correctly, with high-cycle upgrades available.

Typical $200-$450

Raynor Remote & Keypad Programming

Remotes, keypads and car buttons matched and programmed to your opener.

Typical $50-$150

Craftsman Remote & Keypad Programming

Older Craftsman openers with model numbers starting with 139 were built by Chamberlain, so their remotes and parts often match Chamberlain and LiftMaster models from the same era.

Typical $50-$150

LiftMaster Smart Garage Door Opener Setup

LiftMaster is the professional-installer brand of The Chamberlain Group. The color of the learn button on the motor unit shows which remotes are compatible (yellow on Security+ 2.0 models; purple, red, orange or green on older ones), and most current models work with the myQ app.

Typical $100-$900

Amarr Weather Seal Replacement

Amarr, an ASSA ABLOY Group brand, makes residential lines such as Classica, Heritage, Lucern and Oak Summit, as well as commercial doors.

Typical $100-$300

Linear Opener Gear & Sprocket Replacement

Linear openers and remotes are now part of Nice North America. Linear's MegaCode remotes are common on older openers and gate systems.

Typical $125-$275

Garage door stuck, noisy or broken?

Talk to a garage door technician in Latimer, MS now. Tell us what the door is doing and we'll give you a price and an arrival window.

Call NowFree Quote